PROJET AUTOBLOG


Dotmana

source: Dotmana

⇐ retour index

UV-C lamp 3W USB power supply

mercredi 4 août 2021 à 21:00

Want to drive a E17 3W UV-C bulb (the germicidal one, generating ozone or not depending of the version of the glass) from USB (or any battery)?

Use this DDTCCRUB 4S-2A Battery Charger Module Step Up Boost Li-Polymer

Change the RCS resistor from 50mOhm to 125mOhm (0.125 Ohm) to change the charging current to 300mA.

Remember, these bulb have to be supplied 16V (min) so the filament starts glowing, but once the arc is established, current has to be limited to 300mA (settling at around 10V)

Don’t let it run more than few sec on the front of your naked eye/skin.

Interstellar OST: 15.7 kHz high pitched noise

vendredi 25 décembre 2020 à 21:02

Interstellar is an awesome movie, and the sound track is even better.

But after having listened it quite few times the original sound track, I quickly realize there is something wrong, not the loudness war, something worst: noise pickup during recording, not filtered out during mixing.

Track 06: Message from Home showing the 15735Hz peak at 51dB

Almost the complete album is tainted, for example, in this track, “Message from Home”, is a single piano recording showing this noise standing out clearely.

Dont get me started it’s because of the MP3 or format artifact, this is present on any version, MP3, FLAC, and even on Spotify online!

Here is an extract of this sound track, do you hear it? It hurts!

06 – Message from Home extract normal speed

If you cannot hear sounds around 16Khz, no problem, here pitched down version, to 0.5 with the noise is now at 8Khz if you don’t hear it, you may want to consult a specialist.

06 – Message from Home extract half speed

Because it may sound crazy that a multi million dollar movie, OST and sound track composer (Hans Zimmer) get away with this, I’ve looked up and found this reddit thread mentioning it:

Well, I’m not crazy after all and it look like it’s a Pilot Signal at “15.7342657 kHz is used to indicate the presence of MTS stereo.”

So that’s it, there is nothing to do, we are stuck with this (at least I can filter out my own version), but please, mixing engineers, next time, pay attention.

LED light flicker: DIY measure it

samedi 7 novembre 2020 à 13:50

We all experienced it: light flicker! When concentrating on a piece of work or dead tree text, the light suddenly goes berserk and flash like a stroboscope on the dance-floor.

This effect is especially present in LED light fixtures where there is no inertia: incandescent or fluorescent light have a thermal or phosphor inertia and continue to glow a flick of second after the power is cut. But not the LED (even though there is some phosphor in them), this leads to have a close relation of the light intensity and the supply voltage.

Most of LED light bulb are supplied from main, the quality of the AC/DC converter takes a main role here. Because good rectification and filtering cost, manufacturer are cutting them, and you get this effect.

You can find two type of power supply on LED bulbs: simple rectification with LED string to match the AC rectified voltage. Or AC/DC converter with inductor and constant current control (this is what you want).

I wanted to “quantify” it, more that just a feeling, but didn’t want to drop hard cash (k€$ range) for dedicated equipment.

So I used one of the simplest and cheaper photo sensor on the market: a NPN phototransistor, (not a photoresistance as the bandwith is to small), in addition with a 10k resistor, connected to the GND (ring 2) and MIC (sleeve).

Then use a simple Android software, called Oscilloscope

The result is then very straightforward, especially in spectrum analyzer:

Standard office ceilling panels with AC/DC block converter under the drop down ceiling
Ultra cheap LED light bulb COG (chip on glass) with bridge rectifier (4 diodes)
100€/$ photo studio panel with external AC/DC power supply or battery operated

I now always have this small 3.5mm 4 ring photo-transistor adapter in my pocket when shopping light bulb/appliances in home improvement, so I can point it and discard the worst devices.

If someone comes with a better idea, to measure more accurately amplitude and ideal the spectrum (would need a dedicated color sensor though), with an easy to use interface, that would be awesome.

Industrial manufacturing: DFM or planned obsolescence

lundi 20 avril 2020 à 10:20

I’ve stumble upon a fairly common appliance, present in most home, built by million of unit, a TV.

This model is a GRUNDIG 40VLE5324BG with LED backlight: not starting anymore (one could see the “Grunding” logo or “signal not present” when flashing a strong light on it).

After seeking the net for a solution, removing dozen of screws, accessing the 100cm long LCD panel made of ultra thin glass with COG and flex PCB on side, I finally had access to the culprit: No, it was not the capacitor, not the LED driver, not even a LED but a single connector: PCB to PCB connector, designed to decrease assembly time and cost. As these LED string are serial driven (140V @ 400mA), a single failure will render the whole system useless.

Just wiggling the connector would start/stop the backlight:

In this case, slight flex, oxidation or poor connector plating cause the problem, and as the LED as serial connected, the connector is oxidized from long arcing:

And the connector:

Let’s strap these connector with a piece of wire and fix this stuff!

Cheap 5ct clip will render a 500€/USD TV after few years! Hurray to planned obsolescence and global grow and economy!

USB-C iron solder: TS100

jeudi 7 novembre 2019 à 15:54

TS100 is a very good iron solder, with a rated power of 17 to 65W, when powered from 12 to 24V.

While 12V DC jack DC5525 are everywhere, 24V are less but needed if you want more heat to solder larger components or grounds. (better than the TS-80 with the weak 18W anyway)

Supplying from USB-C source with PD 19V 60W takes full advantage of this iron solder.

This hack has been made but not robust enough nor slick to my taste.

This 3 bucks USB-C to DC5.5mm @19V does the job.

Here a RAVPower 60W PD is used

Perfect for my mobile bench with the classic DPS3005 power supply.